Call us for advice - or just to place an order on: 0116 2865141
The Pressure Sensitive Adhesive Specialists in Adhesive Tapes & Glues
This spray adhesive is a polyurethane foam adhesive you can trust, a single-part moisture-cure urethane foam adhesive designed for bonding insulation like ISO boards to a variety of substrates, including: concrete, plywood, cementitious boards and brick Read the full product description
This item qualifies for free Mainland UK shipping
1 Pot Only: £174.12Excluding Tax: £145.10
How many would you like?
Add to your basket »
PSA code: PSAC10 | Manufacturer: TensorGrip | Product condition: New | Stock status: In stock
Ask us a question about this productGet a bespoke quote for this product
Orders are dispatched within 1 - 2 working days
Open your account today for 5% off your 1st order
Free standard mainland UK shippingon all orders over £30 (excluding VAT)
Free advice to make your products last longer
This spray adhesive starter kit comes with everything you need to get up and running quickly. The 22KG TensorGrip® L40 Spray Adhesive, a 12FT Spray Adhesive Glue Hose, and the Spray Glue Gun.
Our TensorGrip® C10 is a spray adhesive for insulation and a bead application adhesive that is low in V.O.C. - suitable for polystyrene bonding applications.
This polyurethane spray adhesive has been designed from a polyurethane foam adhesive you can trust, a single-part moisture-cure urethane foam adhesive designed for bonding insulation like ISO boards to a variety of substrates, including:
Polyurethane foam adhesive is single-part moisture-cure urethane foam adhesive designed specifically for bonding insulation such as ISO boards to a variety of substrates, including concrete, plywood and cementitious boards and brick. Also works with EPS or XPS (expanded or extruded polystyrene). C10 saves time and labour by allowing an operator to apply the adhesive at a rate of 240 square feet (73 square meters) per minute.
Always test a small sample of the materials first to ensure the suitability of the product for the application.
The C10 also works perfectly with EPS or XPS (expanded or extruded polystyrene), and it’ll save you time and labour by allowing an operator to apply it at a rapid rate of 40 square feet (73 square metres) per minute
This polyurethane glue has been developed for use on foam, and has a low VOC (Volatile Organic Compounds).
This product is designed to be applied to one of the
surface of the substrates to be bonded together.
Make sure that surfaces are clean, dry and free from
dirt, dust, oil, loose paint, wax or grease, etc. For
best results, the temperature of the adhesive and
the surfaces being bonded should be between 60
degrees F - 80 degrees F (16degrees C - 27 degrees
Use with adequate ventilation. When possible
we recommend shaking the canister well before
using. Attach and secure hose tightly onto the spray
gun with required tip. Attach the other end of the
hose onto the canister. Make sure the hose-valve
connections are securely tight. Open the valve on the
canister slowly and fully, check for leaks during this
process. Unlock the trigger on the spray gun to start
Prior to use, check compatibility by applying a small
amount of the adhesive on the substrate. This product
may degrade some substrates. Apply adhesive about
10-20 cm (4” – 8”) away at a 90 degree angle to the
surface, applying a uniform, even bead of adhesive
Adhere surfaces and press together with adequate
pressure. Although this product will give sufficient
bond results immediately the full cure is 24 - 48 hours.
Any cured adhesive may be mechanically removed
using a blunt instrument.
Turn valve on canister into the off position, spray out
remaining adhesive left in the hose, disconnect the
spray hose and gun from the canister. Reconnect
the spray hose to a canister of cleaning solvent
(sold separately) and spray out until liquid is clear
which indicates that the hose and gun is clean. If
you choose to leave the hose and spray gun on the
canister, leave the valve on the canister open. Do not
disconnect the hose/gun from the canister. Close and
lock the spray gun.
For optimum results store canister above 18°C during use, but must always be above 10°C. Allow substrates to acclimatise to
normal room temperature (18°C) for 48 hours before bonding. Do not exceed open time of the adhesive. Keep canister off cold
concrete floors during use. If adhesive is expelled wet or as a jet, canister is too cold – move to warm environment and allow
to thoroughly acclimatise before reusing.
MSDS and Technical Data Sheets MUST be read and understood before use. Information contained in this technical literature
is believed to be accurate and offered in good faith for the benefit of the consumer. The company however cannot assume
any liability or risk involved in the use of its chemical products since the conditions of use are beyond our control. Statements
concerning the possible use of our products are not intended as recommendations to infringe on any patent
The technical data contained herein is based on our present knowledge and experience and we cannot be held liable for any errors, inaccuracies, omissions or editorial failings that result from technological changes or research between the date of issue of this document and the date the product is acquired. Before using the product, the user should carry out any necessary tests in order to ensure that the product is suitable for the intended application.
Moreover, all users should contact the seller or the manufacturer of the product for additional technical information concerning its use if they think that the information in their possession needs to be clarified in any way, whether for normal use or
a specific application of our product. Our guarantee applies within the context of the statutory regulations and provisions in force, current professional standards and in accordance with the stipulations set out in our general sales conditions.
The information detailed in the present technical data sheet is given by way of indication and is not exhaustive. The same applies to any information provided verbally by telephone to any prospective or existing customer
If you are not if this contact adhesive tape is right for your individual requirements please do not hesitate to Contact our friendly sales team and we will be happy to help you.
If you require a Certificate of Conformance, please contact us after ordering (either by phone or email) and we will get this sent out to you with your order.
PSA Solutions offers the following shipping options:
If in the unfortunate event that your goods are damaged in transit - or are accepted by PSA Solutions as being faulty due to factors beyond our control - you will be advised to return such goods and a full refund may be offered should you not require replacement goods being dispatched to you. PSA Solutions reserve the right to apply charges for handling and transit on such occasions. It is your responsibility to check the goods in the presence of the courier, and if required note when signing that goods have been damaged. Alternatively just a signature will confirm that goods have been received in good order and that thereafter refunds may not be considered. Please contact us if you do experience any difficulties and we will try our best to help you.
Spray Adhesive Starter Kit - 22Kg TensorGrip L40 | 12FT Hose & Spray Glue Gun
22L L72 One Way Stick Urethane Spray Adhesive
13.7 Litre C10 - Polyurethane Foam Spray Adhesive
22L H45 - KoolTherm Panel Spray Adhesive
22L H30 - Extra Hi-Grab HVAC GP Polystyrene Spray Adhesive
L40 Contact Spray Adhesive / Glue Pot - 22Litre | 22KG
L40 Contact Spray Adhesive / Glue Canister - 110Litre | 110KG
L17 Hi Temperature Resistant Web Contact Spray Adhesive / Glue Pot - 22Litre | 22KG
L17 Hi Temperature Resistant Contact Spray Adhesive / Glue Canister - 110 Litre | 110KG
L22 Non-Mecl Fine Web Spray Adhesive / Glue Canister 22L | 22KG
L22 Non-Mecl Fine Web Spray Adhesive / Glue Canister 110L | 110KG
L40 Contact Spray Adhesive / Glue Can - 500ML
H50 Hi Temp Polystyrene Spray Adhesive / Glue Canister 22L | 22KG
L22 Non-Mecl Fine Web Spray Adhesive / Glue Aerosol Can 500ML
110L H45 - KoolTherm Panel Spray Adhesive
L66 Solid Surface Compatible Spray Contact Adhesive / Glue Aerosol Can 500ML
L66 Solid Surface Compatible Spray Contact Adhesive / Glue 22 Litre