Call us for advice - or just to place an order on: 0116 2865141
The Pressure Sensitive Adhesive Specialists in Adhesive Tapes & Glues
Our TensorGrip® L72 is a high performance, plasticiser resistant adhesive specially formulated for bonding vinyl, rubber and plastics. Read the full product description
This item qualifies for free Mainland UK shipping
Buy in Bulk & Save
1 Pot Only: £478.80Excluding Tax: £399.00
Save with Bulk Buying OptionsPrices shown below Exclude Tax1 Pot = £399.00 / Pot2 Pots - £368.00 / Pot = £736.00 (Save: 7.77% - £62.00)4 Pots - £355.00 / Pot = £1,420.00 (Save: 11.03% - £176.00)
How many would you like?
Add to your basket »
PSA code: PSAL72 | Manufacturer: TensorGrip | Product condition: New | Stock status: In stock
Ask us a question about this productGet a bespoke quote for this product
Orders are dispatched within 1 - 2 working days
Open your account today for 5% off your 1st order
Free standard mainland UK shippingon all orders over £30 (excluding VAT)
Free advice to make your products last longer
This spray adhesive starter kit comes with everything you need to get up and running quickly. The 22KG TensorGrip® L40 Spray Adhesive, a 12FT Spray Adhesive Glue Hose, and the Spray Glue Gun.
Our TensorGrip® L72 is a high performance, plasticiser resistant adhesive specially formulated for bonding vinyl, rubber and plastics. This one sided bond adhesive gives faster and greater efficiencies in areas requiring an adhesive to be applied to one surface only due to physical constraints when applying to both sides. For use in areas on vinyl and other high plasticised flooring and fabric applications that are prone to failing.
This adhesive is suitable for rubber, vinyl, FRL and many metals such as aluminium, and is supplied in a contact adhesive pressure pot.
Always test a small sample of the materials first to ensure the suitability of the product for the application.
This spray adhesive is designed to be applied primarily on 1 side; however, it can be applied to two surfaces to be bonded together. Make sure that surfaces are clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc. For best results, the temperature of the adhesive and the surfaces being bonded should be between 60°F - 80°F (16°C - 27°C).
Use with adequate ventilation. When possible we recommend shaking the canister well before using. Attach and secure hose tightly onto the spray gun with required tip. Attach the other end of the hose onto the canister. Make sure the hose-valve connections are securely tight. Open the valve on the canister slowly and fully, check for leaks during this process. Unlock the trigger on the spray gun to start spraying.
Prior to use, check compatibility by spraying a small test patch of the adhesive on the substrate. This adhesive may degrade some substrates. Spray about 10-20 cm (4” – 8”) away at a 90° angle to the surface, applying a uniform, even coat of adhesive to obtain 80% to 100% coverage of the surface. If necessary, spray another coat of adhesive in areas that appear to need more adhesive. Spray both surfaces to be bonded, one surface vertically and the other surface horizontally. Allow the adhesive to tack off until no adhesive transfers to the knuckle when touched.
Adhere surfaces and press together with adequate pressure. A roller is recommended to apply a uniform pressure to achieve maximum strength. Allow 24 hours for the adhesive to fully cure.
If the spray tip clogs, unscrew the spray tip from the gun and clean with solvent such as lacquer thinner or acetone. Do not use a pin on the spray tip orifice.
Turn valve on canister into the off position, spray out remaining adhesive left in the hose, disconnect the spray hose and gun from the canister. Reconnect the spray hose to a canister of cleaning solvent (sold separately) and spray out until liquid is clear which indicates that the hose and gun is clean. If you choose to leave the hose and spray gun on the canister, leave the valve on the canister open.
Do not disconnect the hose/gun from the canister. Close and lock the spray gun.
Please make sure the following is adhered to when storing this adhesive.
For optimum results store canister above 18°C during use, but must always be above 10°C. Allow substrates to acclimatise to normal room temperature (18°C) for 48 hours before bonding. Do not exceed open time of the adhesive. Keep canister off cold concrete floors during use.
If adhesive is expelled wet or as a jet, canister is too cold – move to warm environment and allow to thoroughly acclimatise before reusing.
MSDS and Technical Data Sheets MUST be read and understood before use. Information contained in this technical literature is believed to be accurate and offered in good faith for the benefit of the consumer. The company however cannot assume any liability or risk involved in the use of its chemical products since the conditions of use are beyond our control. Statements concerning the possible use of our products are not intended as recommendations to infringe on any patent.
The technical data contained herein is based on our present knowledge and experience and we cannot be held liable for any errors, inaccuracies, omissions or editorial failings that result from technological changes or research between the date of issue of this document and the date the product is acquired. Before using the product, the user should carry out any necessary tests in order to ensure that the product is suitable for the intended application.
Moreover, all users should contact the seller or the manufacturer of the product for additional technical information concerning its use if they think that the information in their possession needs to be clarified in any way, whether for normal use or
a specific application of our product. Our guarantee applies within the context of the statutory regulations and provisions in force, current professional standards and in accordance with the stipulations set out in our general sales conditions.
information detailed in the present technical data sheet is given by way of indication and is not exhaustive. The same applies to any information provided verbally by telephone to any prospective or existing customer
If you are not if this contact adhesive tape is right for your individual requirements please do not hesitate to Contact our friendly sales team and we will be happy to help you.
If you require a Certificate of Conformance, please contact us after ordering (either by phone or email) and we will get this sent out to you with your order.
PSA Solutions offers the following shipping options:
If in the unfortunate event that your goods are damaged in transit - or are accepted by PSA Solutions as being faulty due to factors beyond our control - you will be advised to return such goods and a full refund may be offered should you not require replacement goods being dispatched to you. PSA Solutions reserve the right to apply charges for handling and transit on such occasions. It is your responsibility to check the goods in the presence of the courier, and if required note when signing that goods have been damaged. Alternatively just a signature will confirm that goods have been received in good order and that thereafter refunds may not be considered. Please contact us if you do experience any difficulties and we will try our best to help you.
Spray Adhesive Starter Kit - 22Kg TensorGrip L40 | 12FT Hose & Spray Glue Gun
22L L72 One Way Stick Urethane Spray Adhesive
22L C10 - Polyurethane Foam Spray Adhesive
22L H45 - KoolTherm Panel Spray Adhesive
22L H30 - Extra Hi-Grab HVAC GP Polystyrene Spray Adhesive
L40 Contact Spray Adhesive / Glue Pot - 22Litre | 22KG
L40 Contact Spray Adhesive / Glue Canister - 110Litre | 110KG
L17 Hi Temperature Resistant Web Contact Spray Adhesive / Glue Pot - 22Litre | 22KG
L17 Hi Temperature Resistant Web Contact Spray Adhesive / Glue Canister - 110 Litre | 110KG
L22 Non-Mecl Fine Web Spray Adhesive / Glue Canister 22L | 22KG
L22 Non-Mecl Fine Web Spray Adhesive / Glue Canister 110L | 110KG